EXPLORE MORE CATEGORIES
- Home
- »
- Products & Services
- »
- IWL Waterproofing Products
IWL Waterproofing Products
Leading Manufacturer of pypkote pipeline corrosion resistant tape, bituminous app membrane 3mm for waterproofing, iwl sbs app membrane self adhesive bituminous membrane, iwl liquikote bitumenous clay type emulsion, iwl waterproofing membrane and iwl bitumen emulsion from Chennai.
Pypkote Pipeline Corrosion Resistant Tape
Product Price: Rs 2,350 / RollGet Best Price
Product Brochure
Product Details:
| Tape Width | >100 mm |
| Usage/Application | Industrial Use |
| Tape Length | 10-20 m |
| Color | BLACK |
| Brand | IWL / STP |
| Width | 150mm,250mm,500mm and 1000mm |
| Softening Point | 65 to 121 Deg C |
| Thickness | 4 mm |
| Penetration | 3 to 20 At 25 Deg C |
| Filler | 20 to 30 % |
Description
Pypkote 4 mm is a Pipeline Corrosion Resistant Tape conforming to IS 10221 Appendix B specification. It comprises of a Tar based Polymeric mix supported on a fabric of high tensile strength Fibreglass. The Polymeric mix is specially manufactured to have properties of high softening point, high penetration and high resistance to ageing. Tape is terminated on both exteriors by thermofusible HMHDPE Film which aids in the installation process.
Application is fast and easy. The pipe surface is first cleaned with a wire brush. IWL CS is applied on pipes immediately after cleaning. This is to prevent any further accumulation of rust on the pipe. After the primer is applied on the pipe, it is allowed to dry for about 30 minutes till it becomes touch dry. Before adhering the tape to the pipe, it is advisable to gently heat the primer coated pipe by a run of LPG torch. The bottom surface of the tape is heated by LPG Torch or any heat source. The tape is wrapped either by spiral or circumference method over the pipe. By heating the primer coated pipe and by removing the bottom polyethylene from the tape before wrapping, better adhesion between the tape and pipe is obtained. Overlaps are maintained with a minimum of 12 mm. Afinal coat of White Wash is done immediately over the entire coated pipe.
Over weld joints, the tape is applied after the necessary welding and testing of the joints are completed. The procedure for application of tape is the same as bare pipe procedure. Overlaps on each side of the weld joints are to be 50 mm. Pypkote tape is recommended for application closer to the time of pipe erection and lowering inside trenches to avoid damages to Pypkote. While in storage, Pypkote Rolls must be stacked properly under cover
Yes! I am InterestedRequest A Callback
Bituminous App Membrane 3mm For Waterproofing
Product Price: Rs 159 / Square MeterGet Best Price
Minimum Order Quantity: 10 Square Meter
Product Brochure
Product Details:
| Material | Bitumen |
| Thickness | 3 mm |
| Usage/Application | Water Proofing |
| Brand | IWL |
| Pilability | 2 to -5 Deg C |
| Water Absorption | <0.15 % |
| Crosswise Tensile Strength | >300 N/5 cm |
| Crosswise Elongation | >20 % |
| Softening Point | Min.150 Deg C |
| Penetration | 20-35 At 25 Deg C |
Yes! I am InterestedRequest A Callback
IWL SBS APP Membrane Self Adhesive Bituminous Membrane
Get Latest Price
Product Details:
| Minimum Order Quantity | 10 Square Meter |
| Thickness | 2MM | 3MM |
| Membrane Type | Bituminous |
| Top Finish | Film faced |
| Roll Size | 1x10 m |
| Application Area | Roof, Basement, Bathroom, Retaining wall |
| Adhesive Type | Bitumen based |
| Service Life | 5+ years |
Product: IWL Self Adhesive SBS APP Membrane
Size: 1m x 10m roll
Thickness: Available in 2mm & 3mm
✔ Self-adhesive, peel & stick application
✔ No torching or heating required
✔ Suitable for terrace, roofs, basements, bathrooms & foundations
✔ Strong bonding and long-lasting waterproofing
✔ Economical, easy & clean installation
Brand: IWL
Product Type: Self Adhesive SBS / APP Waterproofing Membrane
Material: Modified bitumen with polyester reinforcement
Thickness: 2mm / 3mm
Roll Size: 1m x 10m (10 Sq. Mtr. per roll)
Surface Finish: Polyethylene / Release Film
Application Method: Peel & Stick (Self Adhesive)
Temperature Resistance: High UV & heat resistance
Uses: Roofs, terraces, basements, walls, water tanks, bathrooms, foundations
Yes! I am InterestedRequest A Callback
Iwl Liquikote Bitumenous Clay Type Emulsion
Get Latest Price
Product Brochure
Product Details:
| Minimum Order Quantity | 80 Kg |
| Grade Standard | RS1 |
| Packaging Size | Kg |
| Penetration Grade | 80/100 |
| Usage/Application | Bituminous Waterproofing |
| Type Of Bitumen | Modified |
| Country of Origin | Made in India |
Liquikote is a high-performance water-based bituminous cold applied clay type emulsion specially formulated for effective waterproofing applications. It contains finely crushed bitumen dispersed in water, blended with inert fillers and selected fibres to form a strong, shock-resistant, and waterproof protective coating. Liquikote provides a smooth finish, excellent flow, and direct applicability even on wet surfaces, making it an ideal choice where heating of bitumen is not desirable or prohibited.
Applications:
-
Waterproofing of leaky walls and damp surfaces
-
Roof waterproofing treatment (even under wet conditions)
-
Industrial & residential waterproofing works
-
Surfaces where heating of bitumen is restricted
Advantages:
-
Forms an impermeable coating resistant to water
-
Excellent resistance to saline atmosphere & industrial fumes
-
Withstands low temperature cracking & vibrations
-
Provides durable protection with smoother finish and better flow
-
Easy cold application – no heating required
Application Methodology:
-
Clean the surface thoroughly with a wire brush to remove dirt and loose particles.
-
Dilute Liquikote with water in a 1:1 ratio and apply as a primer.
-
Once the primer dries and turns black, apply Liquikote directly on the surface.
-
After setting, spread coarse sand or crushed stone chips over the coating for enhanced durability.
Health & Safety:
-
Ensure container lid is tightly closed when not in use.
-
Use gloves and goggles during application.
-
Wash hands with water after use.
Packing & Storage:
-
Available Packs: 20 kg & 200 kg drums
-
Storage: Keep in a cool, dry place in airtight containers, away from direct heat or sunlight.
-
Shelf Life: 6 months in original sealed condition.
Yes! I am InterestedRequest A Callback
Iwl Waterproofing Membrane
Product Price: Rs 2,220 / RollGet Best Price
Product Details:
| Thickness | 4 mm |
| Usage/Application | Water Proofing |
| Color | Black |
| Packaging Type | Roll |
| Water Absorption | <0.15 % |
| Penetration | 20-35 At 25 Deg C |
| Lengthwise Tensile Strength | >350 N/5 cm |
Yes! I am InterestedRequest A Callback
Iwl Bitumen Emulsion
Get Latest Price
Product Brochure
Product Details:
| Minimum Order Quantity | 60 Litre |
| Packaging Size | 20 L |
| Type | Bitumen Coating |
| Color | Black |
| Form Of Paint | Liquid |
| Brand | Iwl |
| Country of Origin | Made in India |
Packing20 Ltr, 200 Ltr Metal Drums
Yes! I am InterestedRequest A Callback
Iwl Hyperself Aluminum Flash Tape
Get Latest Price
Product Brochure
Product Details:
| Minimum Order Quantity | 3 Roll |
| Tape Length | 10 Meter |
| Tape Width | 4 Inch |
| Material | Aluminium |
| Color | Silver |
| Country of Origin | Made in India |
Hyperself is a premium self-adhesive bituminous waterproofing membrane manufactured to the highest international standards. It is available with a variety of top surfaces such as PE, Aluminium, Copper, and HMHDPE film for enhanced protection. The adhesive compound ensures excellent flexibility even at low temperatures, high tensile strength, and superior adaptability to contours and structural movements.
With strong dimensional stability, elongation, and chemical resistance, Hyperself is an ideal choice for long-lasting waterproofing applications across multiple industries.
Applications:
-
Waterproofing of basements (horizontal & vertical structures)
-
Terraces, flat & sloped roofs
-
Tunnels & underground structures
-
Multi-level floors & insulation systems
-
Protection of joints
-
Anti-corrosive tapes for structural elements
Key Advantages:
-
Cold-applied & self-adhesive – No heating required
-
Excellent flexibility & elongation for structural movements
-
High tensile strength & dimensional stability
-
Resistant to chemicals, saline atmosphere, and corrosion
-
Easy & fast application – no special equipment required
-
Available in multiple surface finishes (PE, Aluminium, Copper, HMHDPE)
Application Methodology:
-
Clean the surface thoroughly – remove dust, sharp projections, and moisture.
-
Apply suitable primer (IWL Primer / IWL CS recommended).
-
Unroll Hyperself and bond it completely to the prepared surface.
-
Lay rolls from the lowest point upwards to avoid counter-gradient overlaps.
Packing & Storage:
-
Standard Roll Size: 1m x 20m, Thickness: 1.5 mm (other sizes available on request)
-
Packing: Rolls with protective release liner
-
Storage: Keep in a cool, dry, covered place away from direct sunlight & heavy loads
-
Note: Not suitable for pavements as it cannot withstand heavy container loads
Yes! I am InterestedRequest A Callback
Iwl Reflex Aluminium Waterproofing Paint
Get Latest Price
Product Brochure
Product Details:
| Minimum Order Quantity | 80 Kg |
| Packaging Size | 20L |
| Finish | High Gloss |
| Color | Silver |
| Brand | Iwl |
Application ProcedureStep: 1 Stir before application on the prepared substrate. Step: 2 A thin coat of Reflex paint is applied using brush or spray depending on the application area and allowed to dry for 1-2 hours. Step: 3 Apply the next coat of Reflex paint, to result in good aluminium finish surface. Usually two coats are recommended.CoverageCoverage of Reflex paint on metal substrate is 6-10 m² / Kg / coat and on concrete substrate is 2.5-3 m² /per Kg/ coat.*Coverage may vary depending upon the surface condition, temperature, wind velocity, applicator ’s skill, surface porosity and quality of substrate.Cleaning Clean all tools used for application using any standard solvent to avoid hardening.LimitationsHighly inflammable, keep it away from fire / heat. Solvent based, therefore, prolonged exposure in closed area should be avoided.
Yes! I am InterestedRequest A Callback
Iwl App Membrane
Product Price: Rs 169 / Square MeterGet Best Price
Product Details:
| Thickness | 1mm|2mm|3mm|4mm |
| Reinforcement | Fibreglass |
| Top Finish | Film faced |
| Roll Size | 1x10 m |
| Softening Point | >100 °C |
| Application Area | Podium, Basement, Water tank, Bridge deck, Roof, Terrace, Multiple Usage |
| Tensile Strength | >650 N/5 cm |
| Elongation | >40 % |
Yes! I am InterestedRequest A Callback
IWL PlastikFelt Bituminous Waterproofing Membrane
Get Latest Price
Product Details:
| Material | PVC |
| Thickness | 1 mm |
| Application Area | Any |
| Roll Size | 1x20 m |
| Application Method | Self adhesive |
| Top Finish | Film faced |
| UV Resistance | UV resistant |
| Service Life | 5+ years |
Plastikfelt is a cost-effective waterproofing membrane designed to provide temporary protection against water penetration for limited durations. It is commonly used in construction and civil works where short-term waterproofing is required before permanent treatment is applied.
Key Features:
-
Provides reliable temporary waterproofing
-
Economical and easy to install
-
Suitable for short-term applications
-
Lightweight, flexible membrane
-
Ideal for covering surfaces during construction work
Applications:
-
Roof protection before final waterproofing
-
Temporary covering for building materials
-
Protection in under-construction structures
-
General purpose moisture barrier in site works
Benefits:
-
Reduces risk of water damage during construction
-
Helps maintain material and surface integrity
-
Saves cost compared to permanent waterproofing systems
Plastikfelt is widely used by contractors, builders, and infrastructure professionals looking for quick, affordable, and temporary waterproofing solutions.
Yes! I am InterestedRequest A Callback
Coldstick Primer
Product Price: Rs 135 / LitreGet Best Price
Product Brochure
Product Details:
| Brand | IWL |
| Coverage Area | 5 SqMtr/Kg |
| Packaging Size | 20 Kg |
| Usage/Application | Industrial |
| Type | Bonding Primer |
Yes! I am InterestedRequest A Callback
Bitumen Peel & Seal Tape
Product Price: Rs 425 / UnitGet Best Price
Minimum Order Quantity: 1 Unit
Product Details:
| Tape Width | >100 mm |
| Tape Length | 10-20 m |
| Backing Material | BITUMEN |
| Brand | GANESH |
| Usage/Feature | INSTANT LEAK REPAIR |
| Color | ALUMINUM SILVER |
| Tape Type | Adhesive |
| Adhesive Type | YES |
| Adhesive Strength | 100% DRY SURFACE |
| Total Thickness | 1.5MM |
| MOQ | 1 |
| Country of Origin | Made in India |
Leaks and Cracks on galvanised /Asbestos sheet / Concrete roofs / Gutters joints, Ducts and Metal Pipes
Advantages:
Ready to use, cold applied, simple and Quick application.
Save time and Cost
No special tools required.
Withstands climatic changes.
Additional Information:
- Production Capacity: 1000
- Delivery Time: 5 DAYS
- Packaging Details: WIDTH 50 / 100/ 150 / 200 LENGTH 10 MTRS
Yes! I am InterestedRequest A Callback
Liquicrete 151 Cementinous Waterproofing
Get Latest Price
Product Brochure
Product Details:
| Minimum Order Quantity | 60 Kg |
| Number of Components | 1-Component Liquid |
| Packaging Size | 20 Kg |
| Application Areas | Bathrooms & Toilets, Interior Walls, Roofs & Terraces, Basements, Swimming Pools |
| Packaging Type | Bucket |
| Surface Of Application | Steel, Plastic, Metal |
| Features | UV Resistant, Anti-Carbonation |
| Country of Origin | Made in India |
Liquicrete 151 is an acrylic-based, polymer-modified cementitious coating system designed for effective waterproofing and surface protection. Ideal for basements, toilets, roofs, swimming pools, water tanks, and general concrete repairs.
Key Features:
-
Excellent bond with most building materials
-
Prevents salt penetration in concrete
-
UV resistant
-
Chemical resistant (mild acids to strong alkalis)
Application Instructions:
-
Ensure surface is clean and free from oil, grease, dirt, or other contaminants
-
Pre-wet concrete surfaces for at least 1 hour (no standing water)
-
Fill surface depressions using filler (Mix: 1 kg cement : 1.5 kg silica sand : 0.52 kg Liquicrete 151)
-
Coating mix: 100 kg cement : 50 kg Liquicrete 151
-
Apply with brush; 2+ coats recommended with 5–6 hours gap between coats
-
No water curing; use polythene sheet in hot/dry conditions to prevent rapid drying
Coverage:
-
Single Coat: 0.73 kg/m²
-
Two Coats: 1.10 kg/m²
Yes! I am InterestedRequest A Callback
Iwl Liquithane Btd Polyurethane Waterproof Coating
Get Latest Price
Product Brochure
Product Details:
| Minimum Order Quantity | 60 Kg |
| Packaging Size | 20 Kg |
| Color | White |
| Packaging Type | Bucket |
| Country of Origin | Made in India |
Uses:● Suitable for different substrates such as concreteroof, hollow bricks, asphalt, balconies and terraces.● Suitable as waterproofing membrane in traditionalwarm roofs, non - insulated and inverted roofstructures.
Advantages● Single component, ready to use with easyapplication.● Quick drying at room temperature and protectsagainst water penetration.● Superior adhesion to concrete surface and excellentwaterproofing property.● Better crack bridging ability and high elongation.● Excellent resistance to UV, hence coating has longerlife.
Packing:20 Kg Plastic pail
Yes! I am InterestedRequest A Callback
Iwl Pypstick
Get Latest Price
Product Brochure
Product Details:
| Minimum Order Quantity | 60 Litre |
| Packaging Size | 20ltr |
| Brand | IWL |
| Usage/Application | Metal |
| Packaging Type | Drum |
| Color | Black |
| Country of Origin | Made in India |
Pypstick is a solvent-based, rubber-modified, synthetic chlorinated primer used for pipe coating and wrapping applications. Designed for cold application, it ensures strong adhesion and surface preparation before protective coatings are applied.
Key Features:
-
Cold applied – easy brush or spray application
-
Excellent adhesion and elasticity
-
Penetrates porous substrates effectively
-
Ideal for pipe coating preparation
Application Instructions:
-
Apply using brush or spray on clean, dry surfaces
-
Allow solvent to fully evaporate before further processing
-
Ensure no open flame is near during application – flammable solvent content
-
Avoid prolonged inhalation, especially in enclosed areas
Packaging:
-
Supplied in 20 Kg tins
Note: Suitable for professional use in industrial pipe coating processes. Handle with proper safety precautions.
Yes! I am InterestedRequest A Callback